Using Kalman Filter Is Digital Signal Processing Based Filter

2.4 VIDEO DENOISING Nowadays digital cameras which is used to capture images and videos are storing it directly in digital form. But this digital data ie. images or videos are corrupted by various types of noises. It may cause due to some disturbances or may be impulse noise. To suppress noise and improve the image performances we use image processing schemes. In this paper they uses Kalman filter to remove the impulse noise. The Kalman filter is digital signal processing based filter. It estimates three states past, present and future of a system.[10] To remove noise from video sequences they utilize both temporal and spatial information. In the temporal domain, by collecting neighbouring frames based on similarities of all images, to remove noise from a video tracking sequence they given a low-rank matrix recovery phenomena. [11] 3. METHODOLOGY ADOPTED 3.1 Wavelength De-noising 3.2 Bilateral De-noising 3.1 WAVELENGTH DENOISING Basically a wavelet is small wave, which has its energy concentrated in time to give a tool for the analysis time varying phenomena. It is easier to remove noise from a contaminated 1D or 2D data using these algorithms to eliminate the small coefficient associated to the noise. In many signals, mostly concentration of energy is in a small number of dimensions and the coefficients of these dimensions are relatively large compared to other dimensions (noise) that has its energy spread over a large number of coefficients. In wavelet thresholdingShow MoreRelatedNeural Recording And Processing Of The Neural Signals1180 Words   |  5 PagesNeural Recording and Processing The most critical element of a Brain Machine Interface (BMI) is the recording and processing of the neural signal. We use an invasive neural signal recording to achieve higher performance of the BMI and to obtain better resolution. We will be recording the neural signal on central sulcus located in the cortex region of the brain. This recording is referred to as Electrocorticography (ECoG). We will be using subdural grid electrodes (surface electrodes) with 48 contactRead MoreElectrocardiogram Research Paper973 Words   |  4 PagesThis paper presents a real-time electrocardiogram (ECG) monitoring system for wearable devices. The system is based on the proposed parallel Delta Modulator architecture with local maximum points and local minimum points algorithms to detect QRS and PT waves. Therefore, using the proposed system and algorithm, real-time PR and RT interval measurements can be achieved. The algorithm is tested with the MIT-BIH Arrhythmia Database and achieves above 99%, 91% , 98% accuracy in QRS complex, P wave, andRead MoreTHEORETICAL STUDY AND PROBLEM DEFINITION REPORT Assignment 2 â€Æ' TABLE OF1900 Words   |  8 PagesPositioning system 5 3.1.5 Digital Camera System 5 3.1.6 RF communication system (Wi-Fi radio transceiver module). 5 3.1.7 Remote Control System 5 3.1.8 Gyro, accelerometer and compass system 5 3.1.9 Ultrasonic range sensors 5 3.1.10 Laser range sensor 5 3.1.11 Digital barometer sensor 5 3.1.12 Power supply 5 3.1.13 Main Processing system 5 3.1.13.1 Auto Pilots Processing 5 3.1.13.2 Video Processing system 5 3.1.13.3 Pattern recognition processing 6 3.1.13.4 Sensor Processing 6 3.1.14 Quad rotor systemRead MoreAccident Spot Identification Using Gsm Gps: Is It Really Accurate?8682 Words   |  35 Pagesbe no hope to survive. To overcome these, GSM and GPS technologies are used. The GPS based vehicle accident identification module contains a vibrating sensor and a GPS modem connected to the microcontroller. When an accident occurs, the vibration sensor gives the signal to the microcontroller, which sends the information to the LCD display through GSM network. The vehicle is tracked for every five minutes using GPS and the position of the vehicle is also send to the mobile in terms of latitude andRead MoreStable and Self Adaptive Routing for Mobile and Ad Hoc Networks Using Cross Layer Design1933 Words   |  8 PagesSystem Design The cross layer based reliable routing algorithm, is designed using the metric from the physical layer, data link layer and transferring it to the network layer to make the routing decisions. This algorithm involves the mobile node cooperatively to establish the route and introduces the radio link stability with extensive cross layer cooperation to establish reliable and stable routes. We have developed this algorithm by modifying the underlying principle of dynamic source routingRead MoreA Review On Prediction Of Chatter Stability1852 Words   |  8 Pagesspindle speed is an effective technology for processing various materials. During milling, unstable self-excited vibrations known as regenerative chatter can occur, causing excessive tool wear or failure and a poor surface finish on the machined work piece. There are several analyzing techniques that are used to increase the stability of the machining process such as, fuzzy arithmetic techniques, stability lobe diagram(SLD),Struct ural dynamic modification. Based on these analyzing techniques how the operatingRead MoreQuality Improvement328284 Words   |  1314 Pagesprinciples and the basis for applying them in a variety of situations. Although statistical techniques are emphasized throughout, the book has a strong engineering and management orientation. Extensive knowledge of statistics is not a prerequisite for using this book. Readers whose background includes a basic course in statistical methods will find much of the material in this book easily accessible. Audience The book is an outgrowth of more than 35 years of teaching, research, and consulting in the